L79xxC. Negative voltage regulators. Datasheet − production data. Features LCV. LCV-DG (1). LCD2T-TR. LCP. LCV Negative Voltage Regulators. OUTPUT CURRENT TO A OUTPUT VOLTAGES OF V THERMAL OVERLOAD PROTECTION SHORT CIRCUIT. LCV from STMICROELECTRONICS >> Specification: Fixed LDO Voltage Regulator, , V to V, V Technical Datasheet: LCV Datasheet.

Author: Vitilar Vuramar
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Science
Published (Last): 17 March 2015
Pages: 140
PDF File Size: 18.83 Mb
ePub File Size: 9.46 Mb
ISBN: 557-3-88252-646-5
Downloads: 62357
Price: Free* [*Free Regsitration Required]
Uploader: Fenririsar

LM regulator doesn’t work by datasheet

How do you get an MCU design to market quickly? How reliable is it? LM regulator doesn’t work by datasheet Hi, Sorry, the capital letters were not meant as “shouting”. Heat sinks, Part 2: I use the proper capacitors for filtering and stability by the application note ST semiconductor’s datasheet.

The time now is LM regulator doesn’t work by datasheet Hi everyone! Replaced capital letters with underlined letters. LM regulator doesn’t work by datasheet You datasheet show the circuit diagram, but from what you have said have datasheeh put the l792cv in series with the ground pin of the the right way around?

FvM mentioned a defective device. The output may be reversed and latch to a small positive voltage in this case. PNP transistor not working 2. And I bought that IC from an other shop. Capital letters are equivalent of shouting as rules say, it is not necessary. But when I have tested the IC with labour supply there wasn’t diode or huge capacitor.


Negative Voltage Regulators

It is different between the and Originally Posted by KlausST. And what is the special load configuration? LM regulator doesn’t work by datasheet I’m aware of a possible problem with 79xx negative voltage regulators that is brought up if they drive a load connected to a positive supply node. LM regulator doesn’t work by datasheet It makes sense and datashret a good idea. Digital multimeter appears to have measured voltages lower than expected.

The schematic of the datasheet should be verified, and it is very likely that it works as it should. You should show the circuit diagram, but from what you have said have you datasbeet the diode in series with the ground pin of the the right way around? But you are not alone with this behaviour. LM regulator doesn’t work by datasheet.

As a simple test, try if the behavior changes with diode just shorted.

LCV Datasheet(PDF) – STMicroelectronics

AF modulator in Transmitter what is the A? Not the schematic from the datasheet. Turn on power triac – proposed circuit analysis 0. Minimum load current is not either.

It was just to highlight that the datasheet circuit is about useless. At V input l712cv the output is V, at V input voltage the output is about V. Actually the current in the negative branch, on the Zeners is mA, which is almost the expected value, but it is interesting that the output voltage is changed INPUT voltage was V with load.


I will attach schematic for you. Equating complex number datasheeet of the other 6. Make sure that the input and common are connected correctly. So 2 same device from another shops produced this error for me actually.

And it will working well if the regulators are unloaded. For the regulator ICs I shifted this voltage down with 8. But I don’t see how an output voltage magnitude above rated voltage can ever happen with a healthy device.

LM regulator doesn’t work by datasheet I agree, that the standard 3 terminal circuit can be well described in words.

I used about 1mm wide, 35um thick copper on the board, maximum length is about 10cm.

Therefore we need information that are not in the datasheet schematic. Under V the regulated output falls down.

L7912CV Datasheet

Could you describe it more? Is it a true “LM” or a second source one? The regulator don’t know nuthin’ from outside its pins. Originally Posted by E-design.

How can the power consumption for computing be reduced for energy harvesting? LM regulator doesn’t work by datasheet I wasn’t aware of this, but datasheet doesn’t specify output voltage for load current below 5 mA I mean datawheet remember that quality though worked for me with zero load current. Choosing IC with EN signal 2.