ISO INTERNATIONAL. STANDARD. ISO. Second edition. Metallic tube connections for fluid power and general use —. Part 2. 37° flare couplings to ISO comprise a body. (1), pressure sleeve (2) and securing nut (3). By exchanging the pressure sleeve, the same coupling can be. The SAE J/ISO standard outlines the general and dimensional requirements for the design and performance of 37° flaring fittings, suitable to be used.
|Published (Last):||19 January 2006|
|PDF File Size:||13.27 Mb|
|ePub File Size:||7.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
Technical drawings—General principles of presentation. In accordance with Adobe’s licensing policy, this file Parts that pass this test may be used for other tests or in production. Test methods for threaded hydraulic fluid power connections Reference number ISO Fitting and stud end standards 1. Your consent to our cookies if you continue to use this website. Reference number ISO IFS PACsecure is a standard that was designed for managing quality and safety related to product packaging.
Tests outlined in this part of ISO are independent of each other and document the method to follow for each test; see the appropriate component International Standard for the test requirements and performance criteria.
Use the same equipment as specified in 5. The cycle rate shall be uniform at 0,5 Hz to 1,3 Hz and shall conform to the wave pattern shown in ISO Test results and test conditions shall be reported on the test data form given in annex A. Access the full version online. Each member body interested in a subject for isp a technical committee has been established has the right to be represented on that committee.
These test methods have been included in several International Standards, but because of their generic application to ports, studs and tube connections for both metric and inch connections, it was agreed that a separate standard should be established.
Light duty L series stud ends. Otherwise test at the minimum torque values supplied by the manufacturer. Connections shall be restrained during the test and the wrench shall be located at the threaded end of the nut hex.
Applicable tests for various fitting and stud end. Seals shall conform to their respective dimensional requirements, and O-rings shall meet 834-2 exceed the ido requirements for grade N general purpose of ISOif applicable. Hardness Torque Pressure at failure Type of failure.
Durable Male Jic 37 Degree Hydraulic Fittings SAE J ISO
Some of the tests described in this part of ISO are considered hazardous. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Heavy-duty S series stud ends – Dimensions, design, test methods and requirements. The work of preparing International Standards is normally carried out through ISO technical committees. The distance between the centrelines of test ports shall be a minimum of 1,5 times the port diameter. This report is based on accounts to which one of the following applies:.
ISO consists of the following parts, under the general title Metallic tube connections for fluid power and general use: Additional tests are being considered. Testing of two samples to confirm that they are capable of withstanding a vacuum of 6,5 kPa 0, bar absolute pressure for 5 min without leakage. One of their six values Adjustable stud torques shall be applied after being backed out one full turn from finger.
O-ring face seal fittings.
Shri Sai Satcharita – Sai Charitra. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or 88434-2, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.
AGJ (ISO 12151-5 / ISO 8434-2 ) – Male JIC 37° – UNF- UN
Test methods for threaded hydraulic fluid power connections 1 Scope This part of ISO specifies uniform methods for the testing and performance evaluation of threaded metallic tube connections and stud ends of ports for hydraulic fluid power.
Light-duty L series stud ends – Dimensions, design, jso methods and requirements. Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Details of the software products used to create this PDF file can be found in the General Info 84434-2 to the file; the PDF-creation parameters were optimized for printing.
Attention is drawn to the danger of burst, fine jets which can penetrate the skin and energy release of expanding gases. Adobe is a trademark of Adobe Systems Incorporated. This is a free 6 page sample. All standards are subject to revision, and parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying the most recent isl of the standards indicated below.