INTERMEC SR61 MANUAL PDF

SR61 – read user manual online or download in PDF format. Pages in total: SR60 Scanner Programmer’s Reference Manual. Intermec Technologies Corporation. Worldwide Headquarters. 36th Ave.W. Everett, WA U.S.A. CK3c Mobile Computer User’s Manual. Intermec operate and service Intermec- manufactured equipment and is not to be released, reproduced, or cordless scanners, such as the SF51 and SR61 through Bluetooth.

Author: Akinokazahn Samugal
Country: Turkey
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 9 December 2017
Pages: 272
PDF File Size: 14.12 Mb
ePub File Size: 14.34 Mb
ISBN: 809-7-11791-395-7
Downloads: 95838
Price: Free* [*Free Regsitration Required]
Uploader: Garr

Do not remove the battery or place the SR61 in a 1-bay charger until the tone stops. Planet Sets the preamble that precedes any data you scan. When the SR61 successfully reads a bar code label, the SR61 creates a single high beep and the status light briefly turns green.

Don’t have an account? Interleaved 2 of 5 command, Interlink firmware upgrade application, described, Intermec computers connecting to, supported, using to configure the SR61, contact information, Ready-to-Work ontermec described, illustration, SmartWedge, described, telephone sr16, ISBT command, Japan Post command, Symbology Identifier Timeout Between Identical Consecutive Codes command that you use when your bar codes contain identical data.

SR61, and how to install, configure, operate, maintain, and troubleshoot it. When you successfully scan a configuration bar code, you hear the setup beep, and the configuration of the SR61 is changed.

When you reset your SR61, the scanner control firmware is intermeec.

Using Vibrate Alert The aiming beam is smaller when the imager is closer to the bar code and larger when it is further away. Flashing When you pull the trigger, the red scanner beam turns on and the SR61 checks for a bar code to read. Use this chapter to understand how to connect the SR61 to a host device and configure the SR61 to communicate with your application. Before You Begin Outside the U.

The SR61 is not discoverable when it is connected to a host device. Resetting The Sr61 Note: Document Change Record This page records changes to this document. Visit the Intermec support services knowledge base Knowledge Central at intermec. The data is entered into your application. When the SR61 is in the 1-bay charger, the status light indicates the battery charging status. By default, the SR61 aimer rs61 flashes repeatedly while the imager attempts to read a bar code. QR Code command, described, radio Maxicode command, described, communications, configuring, MSI command, specifications, Ready-to-Work indicator off, turning off the SR61, described, offline, configuring the SR61 with illustration, EasySet, red light.

  JAIIB SAMPLE PAPERS PDF

Gtin Processing laser scanner only. To scan a bar code label with a laser scanner or 1D linear imager 1 Point the SR61 at the bar code label and hold the SR61 at a slight angle 15 to 25 cm 6 to 10 in from the label. You can check your battery status at any time. This chapter contains these topics: When your SR61 is discoverable, it is visible to other Bluetooth devices in communication range.

Temperature and Environmental Specifications Operating: The sample code included in this document is presented for reference only. Manal of 82 Go. Scanning Bar Codes Long-term exposure to the laser beam can damage your vision.

For security reasons, you can only change the Bluetooth PIN by scanning a bar code.

Intermec SR61 User Guide – Page 1 of 90 |

Trigger Mode Bluetooth communications, or if the SR61 is too far from the host device. Intermec computer to change your SR61 settings.

The symbols are concatenated as they are scanned and can be scanned in any order. Your SR61 emits an error beep without affecting the configuration of your SR61, when you scan a configuration bar code that is damaged or unknown.

INTERMEC SR61 USER MANUAL Pdf Download.

Telephone Support These services are available from Intermec. The SR61 is updated with the new configuration command settings.

For more information, see the EasySet software. The SR61 contains a 1D linear imager, 2D area imager, or laser scan engine to scan bar code data. When you select a lower decode security level, the SR61 can decode bar codes with poorer print quality. To disconnect, scan the disconnect bar code.

  GUILD WARS GHOSTS OF ASCALON PDF

The SR61 is updated with the new sr16 command settings. Before You Begin Before You Begin This section provides you with safety information, technical manuql information, and sources for SR61, and how to install, configure, operate, maintain, and troubleshoot it. Comments to this Manuals Your Name. Sets the preamble that precedes any data you scan. Page 20 To scan a bar code label with a laser scanner or 1D linear imager 1 Point the SR61 at the bar code label and hold the SR61 inteermec a slight angle 15 to 25 cm 6 to 10 in from the label.

Cleaning the SR61 Clean the scanner window as often as needed for the environment in which you are using the SR Setup Beep Setup Beep Enables or disables the setup beep. Patent Information 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; 6,; nitermec 6,; 6,; 6,; 6,; 6, You can change this default setting so that the aimer is always on.

Understanding The Beeps The SR61 is trying to establish a Bluetooth connection with the host computer, or the SR61 is moving out of range of the host computer.

Intermec SR61 User Guide

Troubleshooting Troubleshooting and Maintaining the SR Don’t show me this message again. This chapter contains these topics: You should also be familiar with Manjal communications. This graphic does not include the 0.