INTERCURE 200 PDF

Intercure Primer by International Paint – INTERCURE HS BUFF, VPN: EPA/5/A for only $ Buy online or find out more at Richmond Industrial . Intercure can also be used as a primer for substrates other than blasted steel , e.g. stainless steel, alloys etc. Consult International Protective Coatings for. Product Description. Intercure is an epoxy rich zinc phosphate/micaceous iron oxide primer. Key Features: Rapid cure & recoat capabilities in low.

Author: Yozshut Nilrajas
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 7 April 2013
Pages: 71
PDF File Size: 2.71 Mb
ePub File Size: 20.82 Mb
ISBN: 198-8-45569-112-7
Downloads: 77134
Price: Free* [*Free Regsitration Required]
Uploader: Samur

International Intercure Reference: Surface preparation All surfaces to be coated should be clean, dry and free from contamination. Be the first to write a review for this product! Customer further agrees that we have no liability for any errors or intrrcure contained within the Product Data Sheets. If the shop primer shows extensive or widely scattered breakdown overall sweep blasting maybe necessary.

INTERCURE HS – SAND (KIT / 4G) – L

Always mix a complete unit in the proportions supplied. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method.

Varnish Hybrid Water base. Send us your question. Intercure is not intended for use as a primer for steelwork which may be subjected to immersion conditions.

International Intercure Epoxy Primer :: miproducts – NZs building products search engine

Low trade prices Our best trade prices on everything! Intercure Safety Advice. Intercure HS can also be used as a primer for substrates other than blasted steel, e.

Excessive over application of material on areas such as poorly prepared welds may result in long term stress cracking and so early failure. Consult International Protective Coatings for further details. GTA Do not thin more than allowed by local environmental legislation Mix ratio: Over-application should be avoided as thick films will not be as good a substrate for topcoat adhesion after ageing as those at the specified thickness.

  JEET AAPKI BY SHIV KHERA PDF

The content of this website is our best recommendation and is not advice. VOC values are typical and are provided for guidance purpose only. Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard but have been allowed to deteriorate under good shop conditions for up to days.

Once the unit has been mixed, it must be used within the working pot life specified. Can also be used on site as a rapid curing, maintenance coating.

Intercure HS is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. Thoroughly flush all equipment with International GTA Please ensure you refer to all datasheets for full application information. This product is no longer in stock Grey. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person and not digitally to ensure that the colour is acceptable for its purposes.

The minimum purchase order quantity for the product is 1. Typical Coverage per coat 8. As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges.

Please note that NBS product guidance is not a replacement for the manufacturer’s literature and it is recommended that International Paint Ltd be consulted before specifying. Your browser does not support automatic copy to clipboard. Over-application of Intercure HS will extend both the minimum overcoating periods and handling times, and may be detrimental to long term overcoating properties.

  BERLINER LINIENNETZ PDF

A high solids, low VOC product. Suitable for overcoating within 7 hours in most climatic conditions hence speeding up production and throughput in fabrication shops. However, if necessary, application over prefabrication blast primers can be performed. Typical Coverage per coat. The figures stated above are approximate. Press and move to zoom.

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. However, these phenomena are not detrimental to anti-corrosive performance. Provides quick cure even at low temperatures often encountered in maintenance painting.

The use of alternative thinners, particularly those containing ketones, can severely inhibit the curing mechanism of the coating. This product is no longer in stock.

Work stoppages Do not allow material to remain in hoses, gun or spray equipment. To find out more about producing specifications for building projects visit www.

Intercure® 200

It is inteercure working practice to periodically flush out spray equipment during the course of the working day. Warning Intercure HS is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions.

Suitable for overcoating within 3 hours in most climatic conditions hence speeding up production and throughput in fabrication shops.