IEC 60062 PDF

IEC Edition INTERNATIONAL. STANDARD. NORME. INTERNATIONALE. Marking codes for resistors and capacitors. Codes de marquage. Fifth edition. Marking codes for resistors and capacitors. Reference number. IEC (E). This is a free 5 page sample. Access the full. IEC MARKING CODES FOR RESISTORS AND CAPACITORS.

Author: Zulkidal Zuluran
Country: Papua New Guinea
Language: English (Spanish)
Genre: Literature
Published (Last): 13 April 2004
Pages: 92
PDF File Size: 10.70 Mb
ePub File Size: 3.88 Mb
ISBN: 267-8-84854-341-4
Downloads: 14143
Price: Free* [*Free Regsitration Required]
Uploader: Vijind

K k [nb 4].

RKM code – Wikipedia

Originally meant also as part marking codethis shorthand notation is widely used in electrical engineering to denote the values of resistors and capacitors in circuit diagrams and in the production of electronic circuits for example in bills of material and in silk screens.

The introduction of the letter L in more recent issues of the standard instead of an SI prefix m for milli is justified to maintain the rule of only using uppercase letters for resistances the otherwise resulting M was already in use for mega. Archived PDF from the original on However, the letter E is conflictive with the lec looking but incompatible E notation in engineering, and it may therefore cause considerable confusion as well.

CS1 German-language sources de Interlanguage link template iiec number CS1 Russian-language sources ru Articles to be expanded from December All articles to be expanded Articles with empty sections from December All articles with empty sections Articles using small message boxes. Similar, the standard prescribes the following lowercase letters for capacitances to be used instead of the decimal point: For brevity, the notation omits to always specify the unit ohm or farad explicitly and instead relies on implicit knowledge raised from the usage of specific letters either only for resistors or for capacitors, [nb 1] the case used uppercase letters are typically used for resistors, lowercase letters for capacitors[nb 2] a part’s appearance, and the context.

  EQUALIBERTY POLITICAL ESSAYS PDF

The RKM code[1] also referred to as “letter and digit code for resistance and capacitance values and tolerances” or “R notation”, is a notation to specify resistor and capacitor values defined in the international standard IEC formerly IEC 62 since This page was last edited on 21 Augustat By using this site, you agree to the Terms of Use and Privacy Policy.

List of International Electrotechnical Commission standards. This is not only 600622 brevity for example when printed on the part or PCBbut also to circumvent the problem that decimal separators tend to “disappear” when photocopying printed circuit diagrams.

For example, 1R2 indicates 1. You can help by adding to it.

IEC | IEC Webstore

From Wikipedia, the free encyclopedia. When the value can be expressed without the need for a 6062, an “R” is used instead of the decimal separator. For example, 8K2 indicates a resistor value of 8. Archived from the original on This method avoids overlooking the decimal separatorwhich may not be rendered reliably on components or when duplicating documents.

Oh no, there’s been an error

Views Read Edit View history. The significantly updated IEC This section is empty. Retrieved from ” https: 6062, a lowercase letter m should be used for capacitances whenever possible to avoid confusion.

  LUTRON SL-4013 PDF

The letters G and T weren’t part of the first issue of the standard, which pre-dates the introduction of the SI system hence the name “RKM code”but were added after the adoption of the corresponding SI prefixes.

R E [nb 3]. The notation also avoids using a decimal separator and replaces ifc by a letter associated with the prefix symbol for the particular value. The letters p and n weren’t part of the first issue of the standard, but were added after the adoption of the corresponding SI prefixes.

Irc code letters are loosely related to the corresponding SI prefixbut there are several exceptions, where the capitalization differs or alternative letters are used. The standards also define a color code for fixed resistors. It stems from the fact, that R is used in symbolic names for resistors as well, and it is also used in a similar fashion but with incompatible meaning in other part marking codes.

Date codes for and are obviously wrong. It may therefore cause confusion in some contexts.

Additional zeros imply tighter tolerance, for example 15M0.