HCNW 4504 PDF

HCNW Broadcom / Avago High Speed Optocouplers 1Ch 12mA mW datasheet, inventory & pricing. The HCPL and HCPL contain a GaAsP LED while the. HCPL-J and HCNW contain an AlGaAs LED. The LED is optically coupled to an. Buy Broadcom HCNW# in Avnet Americas. View Substitutes & Alternatives along with datasheets, stock, pricing and search for other Transistor .

Author: Dukinos Mazukasa
Country: Uzbekistan
Language: English (Spanish)
Genre: Marketing
Published (Last): 22 October 2016
Pages: 196
PDF File Size: 15.4 Mb
ePub File Size: 7.19 Mb
ISBN: 932-7-85154-666-1
Downloads: 70209
Price: Free* [*Free Regsitration Required]
Uploader: Vudojind

The LED is optically coupled to an integrated high gain photo detector.

HCNW 데이터시트(PDF) – Agilent(Hewlett-Packard)

Hcnq bypass capacitor between pins 5 and 8 is recommended. An insulating layer between a LED and an integrated photodetector provide electrical insulation between input and output. Separate connections for the photodiode bias and outputtransistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base hdnw capacitance. Option data sheets available. Contact Agilent sales representative or authorized distributor for information.

Use of nonchlorine activated fluxes is highly recommended.

These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered.

There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances.

  GEOMETRIA SAGRADA DRUNVALO PDF

Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. These optocouplers are suitable for “safe electrical isolation” only within the safety limit data.

Maintenance of the safety data shall be ensured by means of protective circuits. The Input-Output Momentary Withstand Voltage ncnw a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 hcns together. Under TTL load and drive conditions: See Option data sheet for more information. Use of a 0.

F bypass capacitor connected between Pins 5 and 8 is recommended.

DC and Pulsed Transfer Characteristics. Current Transfer Ratio vs.

Agilent Technologies HCNW Optocoupler Lot -5 | eBay

Logic High Output Current vs. Propagation Delay Time vs. When inverter power transistors switch Q1 and Q2 in Figure 17it is essential that they never conduct at the same time. Extremely large currents will flow if there is any overlap in their conduction during switching transitions, potentially damaging the transistors and even the surrounding circuitry.

Minimizing this dead time is an 45504 design goal for jcnw inverter designer. The importance of these specifications is illustrated in Figure Most inverters are designed such that the power 45044 turns on when the optocoupler LED turns on; this ensures that both power transistors will be off in the event hnw a power loss in the control 45504.

Inverters can also be designed such that the power transistor turns off when the optocoupler LED turns on; this type of design, however, requires additional fail-safe circuitry to turn off the power transistor if an over-current condition is detected. The timing illustrated in Figure 17 assumes that the power transistor turns on when the optocoupler LED turns on.

  HIOKI 3198 MANUAL PDF

The LED signal to turn on Q2 should be delayed enough so that an optocoupler with the very fastest turn-on propagation delay tPHLmin will never turn on before an optocoupler with the very slowest turn-off propagation delay tPLHmax turns off. To ensure this, the turn-on of the optocoupler should be delayed by an amount no less than tPLHmax – tPHLminwhich also happens to hcna the maximum data sheet value for the propagation delay difference specification, tPLH – tPHL.

Although tPLH-tPHL max tells the designer how much delay is needed to prevent shoot-through current, it is insufficient to tell the designer how much dead time a design will have. Calculating the maximum dead time is slightly more complicated.

(PDF) HCNW4504 Datasheet download

The difference between the maximum and minimum values depends directly on the total spread in propagation delays and sets the limit on how good the worst-case dead time can be for a given design.

Therefore, optocouplers with tight propagation delay specifications and not just shorter delays or lower pulse-width distortion can achieve short dead times in power inverters. It is important to maintain accurate LED turn-on delays because delays shorter than tPLH – tPHL max may allow shootthrough currents, while longer delays will increase the worst-case dead time.

For technical assistance call: