FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Zulkilabar Mautilar
Country: Australia
Language: English (Spanish)
Genre: Automotive
Published (Last): 4 April 2006
Pages: 153
PDF File Size: 2.70 Mb
ePub File Size: 17.34 Mb
ISBN: 817-9-86533-189-5
Downloads: 73319
Price: Free* [*Free Regsitration Required]
Uploader: Mikarisar

Follow the procedure below for wiring and configuration of the inverter. Torque bias gain adjustment BTBG. A dielectric strength test will cause breakage of the inverter similarly to the Megger test if the test procedure is wrong.

Take an attention for this structure to connect wires to main output secondary terminals.

Fuji Electric FRENIC-Lift series Instruction Manual

Recommended Wire Sizes 2. Ensure that the circuit breaker capacity is equivalent to or lower than the recommended capacity. Brake control by time 2: Page 54 F codes: Insulation Test A dielectric strength test manua cause breakage of the inverter similarly to the Megger test if the test procedure is wrong. Page 38 Table 2.

In no event will Fuji Electric Co. Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances Page Page 49 An undervoltage or an alarm has been occurred. Using this adapter greatly For the tuning procedure, refer to the instruction manual of the option card.

  AALMI MALOOMAT IN URDU PDF

Page 17 When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally.

Do not hold covers or individual parts only. Install FRENIC-Lift in compliance with the local liift, Described below for an example, a procedure shows an installation of the inverter in compliance with regulations in Japan.

Consult your Fuji Electric representative. Page 48 Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option.

Keep this manual in a safe place until this product is. Otherwise fire or an accident could occur.

Torque limit time 0. Torque limit level is F Read through this instruction mabual and be familiar with the handling procedure for correct use. Doing so could cause failure. Refer to Chapter 2 Section 2.

Three-phase v series, three-phase v series, single-phase mnual series 6 pages. For the motor, check the rated values printed on the nameplate of the motor.

FRENIC-Lift | Fuji Electric Global

Tuning offset angle of the magnet pole Before to proceed to running a synchronous motor, be sure to tune offset angle of the magnet pole.

  DYNAMICS OF STRUCTURES BY RAY CLOUGH & JOSEPH PENZIEN PDF

Speed monitor Select by E48 3: Megger test of main ljft Use a VDC Megger and shut off the main power supply without fail during measurement. Remove the screw fastening the cable guide plate, and manuual out the plate. When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally. Contact your Fuji Electric representative. Page 59 H codes: Page 18 1 Remove all of the base fixing screws from the top and bottom of the inverter.

Refer to Chapter 5, Section 5. Precautions for use Manusl a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur.

Driving gener- When high starting torque is required or quick acceleration or deceleration al-purpose motor Selecting is required, select an inverter with a capacity one size greater than the lif standard.