international certification bodies for its quality system and environmental management system. E5jK-T Series. E5CK-T. E5AK-T/E5EK-T. 1/4 DIN. 1/8 DIN. Omron E5AK Controllers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Omron E5AK Controllers. E5AK-TAA AC Omron Automation and Safety Controllers PROCESS CONTROLLER datasheet, inventory, & pricing.

Author: Shakalabar Meztijas
Country: Saudi Arabia
Language: English (Spanish)
Genre: Career
Published (Last): 25 February 2007
Pages: 253
PDF File Size: 7.75 Mb
ePub File Size: 8.3 Mb
ISBN: 276-9-15194-520-5
Downloads: 38011
Price: Free* [*Free Regsitration Required]
Uploader: Gronos

Each press of e5wk key switches between the auto and manual opera- tions. The fol- lowing diagram shows the relationship between option units and mounting positions.

Page The display changes to [ ] 0mA calibration display. Don’t show me this message again. Page The display changes to [ ] 5 V calibration display. However, note that the settings of protected parameters are still valid, and are not displayed regardless of the conditions of use. Make sure that the stop bit, data length, parity and baud rate of the host computer and the E5AK controller are matching.

Check the communications condition. The display changes to the menu display. Setting Alarm Type 3.

SP The output ranges of the SP setting, set point or process value when temperature input is selected are the ranges sup- ported by the selected sensor.

Of these, only the alarm assigned as the output can be used. Press key to return the display to [ F Calibration: Set point Stable range Set to However, note that when thermocouple R, S, E, B, W or PLII is used, the cold junction compensator and the compensating conductor can be substi- tuted with the cold junction compensator and the compensating con- ductor for thermocouple K.



Controllers must not be closely mounted vertically or horizontally. PID control, standard con- trol or heating and cooling control. Set the control period taking the control characteris- tics and life expectancy of the controller into consideration.

Page 84 PID control, standard con- trol or heating and cooling control. This character must be inserted before the lead- ing byte. Setting Up 2 Draw out the internal mechanism towards omrom holding both sides of the front panel. Dead band Hysteresis heat. Read this chapter only when the controller must be calibrated.

Page 3 Conventions Used in This Manual J Meanings of Abbreviations Sometimes the following abbreviations are used in parameter names, figures and in text explanations. Page setup mode can be used. F Meaning Calibration data is in error. Page 6 Pay Attention to the Following when Installing this Controller F If you remove the controller from its case, never touch nor apply shock to the elec- tronic parts inside.

Control output cool2: Page numbers refer to previous version. For details on how to use the controller and parameter settings, see Chapters 2 onwards. So, 3-position control is made possible. Nx-series machine automation controller system units pages.

Conventions Used in this Chapter For example, in the fol- lowing configuration, connect the terminator to the host unit and unit No. No part of this publication may be reproduced, stored in a retrieval system, or trans- mitted, in any form, or by any means, mechanical, electronic, photocopying, recording, recording, or other- wise, without the prior written permission of OMRON.


However, note that when the set point limiter is reset, the set point is forcibly changed to the upper-or lower-limit value of the set point limiter if the set point is out of the limiter range. Memory error F Meaning Internal memory operation is in error.

Omron E5AK-AA2-500 Processor/Controller

The following table shows the relation- ship between event inputs and set points 0 to 3. If the heater power supply is turned conditions ON after turning the E5AK power supply On, the heater burnout alarm is output. A nega- tive setting sets an overlap band.

Page Switching with Manual operation. The following figures shows the effect on data after passing through the digital filter. Page J Output Omfon Ratings and Characteristics Ratings and characteristics conform to the output unit mounted on the controller. Set the STV output to 0 mA. Command Configuration The start character.

Omron E5AK-AA Processor/Controller | eBay

About The Communications Function 1. The following conventions are used to indicate and classify precautions in this manual.

In HT hunting tuning mode, when hunting occurs, the PID constants are amended to suppress the hunting. In this mode, you can