E3C-VS1G OMRON PDF

Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Takasa Zolorr
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Health and Food
Published (Last): 1 October 2014
Pages: 377
PDF File Size: 9.99 Mb
ePub File Size: 20.71 Mb
ISBN: 912-3-92869-265-9
Downloads: 73319
Price: Free* [*Free Regsitration Required]
Uploader: Nakree

When in doubt, special model numbers may be assigned to? This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance. Cable Tensile Strength When e3v-vs1g the cable, do not subject the cable to a tension greater than that indicated in the following table. Doing so may result in damage from burning and fire, particularly if the liquid is flammable. Do not use thinner or other organic solvents.

Be sure to connect or disconnect the connector after turning OFF the Sensor. Lock and unlock the fibers at an ambient temperature of?

Typical measures are as given in the following table. The lens, however, is plastic.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross

AC Two-wire Sensors Example: Countermeasure Concept Use a Sensor with the interference prevention function. The lens, case, and fiber covering are made of plastic, so this setup cannot be used if there is a possibility of contact with solvents that will corrode or degrade e. The axis from the center of the lens to the center of the omgon for the Emitter and the axis from the center of the lens to the center of the reception area for the Receiver.

  IMUNOLOGIA BASICA PDF

Do not use it for lmron purposes.

EE11 Check the parallel movement distance range in the catalog, verify the set distance between adjacent Sensors, and install the Sensors accordingly at a distance at least 1. For this type of application, separate the Sensors by at least 1. Precautions for Safe Use To ensure safety, always observe the following precautions. Please know and observe all omronn of use applicable to the products.

Hold the connector cover to connect or disconnect the connector. Placing them in the same conduit or duct may cause damage or malfunction due to induction interference. Use the following methods to attach and remove Fiber Units.

Exceptions are indicated in Safety Precautions in individual product information. Separate Sensors to distance where interference does not occur.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch | eBay

As a general rule, wire the Sensor in a separate system, use an independent metal conduit, or use shielded cable. Insert a capacitor, etc. It is our practice to change model numbers when published ratings or features are changed, or when signi?

Close mounting of Sensors is possible by alternating the Emitters with the Receivers in a zigzag fashion up to two Sensors. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and e3c-vs1t out the fibers.

  EM HAUPTKURS PDF

If not grounded, switching noise in the power supply may cause malfunction. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Radiant noise Ingress of high-frequency electromagnetic waves directly into Sensor, from power line, etc.

If the Sensor and the load are connected to separate power supplies, turn ON the Sensor power before turning ON the load power. Any exceptions to this rule are indicated in Safety Precautions in individual product information.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch

Refer to e3cvs1g values in the above table to check bend-resistant performance under actual working conditions. Lens and Case The lens and case of the Photoelectric Sensor are primarily made of plastic. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

Doing so may cause explosion or burning. They are rather values from samples taken from production lots, and are provided for reference as guidelines. Secure the connector cover by hand.