Test Method for Determination of Hydraulic Conductivity of Porous Material Using a Rigid-wall Compaction-Mold Permeameter. Start. Standard ASTM standard · ASTM D Status: Withdrawn · Replaced by: ASTM D Soil and Rock (I): D – D (ASTM VOL ). ASTM D Standard Test Method for Measurement of Hydraulic Conductivity of Porous Material Using a Rigid-Wall, Compaction-Mold.

Author: Mirisar Fenrizuru
Country: Burkina Faso
Language: English (Spanish)
Genre: Medical
Published (Last): 25 April 2010
Pages: 433
PDF File Size: 2.52 Mb
ePub File Size: 3.27 Mb
ISBN: 827-5-47061-504-4
Downloads: 88323
Price: Free* [*Free Regsitration Required]
Uploader: Baran

In cases where it is essential to saturate the test specimen fully with water, the compacted specimen may be tested using Test Method D The problem tends to be of minimal significance for materials that swell when exposed to water for example, compacted, clayey soils but can be a very serious problem for materials that might tend to shrink and pull away from the walls asstm the permeameter.

Users of this standard are axtm that compliance with Practice D does not in itself ensure reliable results. By tradition in U.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applic. Ashm is a problem adding monitoring – please try again later There is a problem adding the subscription – please try again later. Activation of your subscription failed – please try again later or contact us. Therefore, the results should be applied to field situations with caution and by qualified personnel.


Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Kontakt venligst Dansk Standard. However, when the hydraulic gradient acting on a test specimen is changed, the state of stress will also change, and, if the specimen or pore fluid is compressible, the volume of the test specimen or pore fluid will change. The printed version is available at half price when you buy the electronic version. By tradition in U.

ASTM D5856

Username or password invalid. This test method applies to porous materials containing little or no air. The test method is designed to minimize the amount of air in the test specimen. Do not show this again. Activation of monitoring failed – please try again later or contact us. Are you sure you want to unsubscribe? Du abonnerer allerede dette emne. You must be logged in to sign up for monitoring You must be logged in to sign up for subscription. However, this test method is only intended to be used when water is the permeant liquid.

The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. It was not possible to unsubscribe – please try again later or contact the Danish Standard Please adtm sure you are logged in. Test Method D is recommended for any material that tends to shrink when exposed to the permeant liquid. Permeation with other liquids, such as chemical wastes, can be accomplished using astk similar to those described in this test method.

  D.S.0181 SABS PDF

Reliable results depend on many factors; Practice D provides a means of evaluating some of those factors. Link to Active This link will always route to the current Active version of the standard. It is not possible to buy in the shop – please contact us.

ASTM D Standard

Please choose number of devices you want to open the document on. However, this test method does not ensure complete saturation of the test specimen with water. The hydraulic conductivity of compacted materials that have hydraulic conductivities greater than 1? Historical Version s – view previous versions of standard.

Continue shopping Proceed to checkout.

Are you sure you want to unsubscribe monitoring? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the asstm of regulatory limitations prior to use.

Experience has sometimes shown that flow patterns in small, laboratory-prepared test specimens do not necessarily follow the same patterns on large astmm scales and that hydraulic conductivities measured on small test specimens are not necessarily the same as larger-scale values.