ASTM B214 PDF

The particle size distribution of a metal powder affects its behavior in P/M processing and other applications of these materials. The test method may be part of. ASTM B Standard Test Method for Sieve Analysis of Metal Powders. standard by ASTM International, 04/01/ View all product details. Most Recent. Buy ASTM B Standard Test Method for Sieve Analysis of Metal Powders from SAI Global.

Author: Mikagal Tojabar
Country: Laos
Language: English (Spanish)
Genre: History
Published (Last): 5 July 2006
Pages: 218
PDF File Size: 6.99 Mb
ePub File Size: 8.32 Mb
ISBN: 592-2-26735-389-4
Downloads: 2259
Price: Free* [*Free Regsitration Required]
Uploader: Gole

Remove the fraction collected in the pan and weigh. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Approved April 1, It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Add the difference between this sum and the mass of the test portion in accordance with Section 6 to the mass of the fraction collected in the pan. Each of twelve sstm made awtm tests on four powder samples using each of two sets of sieves.

Standard Test Method for Sieve Analysis of Metal Powders

Series and Tyler Series have also been deleted. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. A portion of 40 to 60 g shall be used when the apparent density of the powder is less than 1.

The hold down arm of the sieve shaker shall be? Report any fraction that is less than 0. Customer comments No comments were found for ASTM B – 07 standard test method for sieve analysis of metal powders.

  LIVRO DO KOTZ EM PDF

Over time, the correcting results should continually be evaluated. Measurement accuracy can be significantly increased by the parallel use of up to three flow velocity sensors. Precision and Bias4 9. For circulated sieves or by analogy matched sieves obtained by two laboratories R can be calculated from the following equations: This standard has been approved for use by agencies of the U.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

The values given in parentheses are for information only. Brush any material adhering to the bottom surface of the sieve and the lower frame with a soft brush into the next? The test method may be part of the purchase agreement between powder supplier and user, or it may be an internal quality control test for either.

Benefits Highest measuring accuracy for Last previous edition approved in as B — Originally approved in NOTE 1—The mm diameter sieve is most commonly referenced as an 8 in.

Repeat this process for each sieve in the nest. Standard Test Method f A number in parentheses indicates the year of last reapproval. Aastm test portion should be obtained in accordance with Practices B A second set of sieves was chosen by each laboratory from its in-house sieve stock.

The mobile NivuFlow Mobile flowmeter was specially developed for wastewater applications in part filled canals as well as in part filled and full pipes. In addition to the asfm listed in Table 1, a cover and collection pan are also required. NOTE 3—For some materials, for example brittle and friable materials, the 15 minutes may be too long.

Standard – Standard Test Method for Sieve Analysis of Metal Powders ASTM B –

Committee B09 has identi? ASTM D If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Standard Series in Table 2 and examples of the Old U.

  BLOQUEO DE PUDENDOS TECNICA PDF

Other types of sieve shakers are also available, but their precision and reproducibility have not been determined. Repeat the test if error persists.

By comparing sieve tests on the same sample, run in both the master set and the working set, a factor can be established for correcting results on the working sieves. Report the actual time period of sieving, if it is different than 15 minutes.

The values given in parentheses are for information only. Flavoring for foodstuffs, active ingredients for pharmaceuticals or corrosion-inhibiting substances in oil production are just a few examples. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Standard Series Test Sieves.

Series has been deleted and the columns for the Old U. No comments were found for ASTM B – 07 standard test asm for sieve analysis of metal powders.

The test method may be part of the purchase agreement between powder supplier and user, or it may be an internal quality control test for either. Then fasten the sieve assembly securely in the sieve shaker and operate the machine for a period of 15 minutes.

sstm Approved October 1, The entire apparatus shall be rigidly mounted by bolting to a solid foundation, preferably of concrete. Innovation, originality and market relevance: