APLUS Integrated Circuits AP datasheet, (AP89xxx) Voice OTP IC (1-page ), AP datasheet, AP pdf, AP datasheet pdf, AP Details, datasheet, quote on part number: aIVR aP · aIVR Tandard CMOS Process. CM Specifications: Output Voltage: to . Details, datasheet, quote on part number: AP aP · aIVR Tandard CMOS Process. CM Specifications: Output Voltage: to volts.
|Published (Last):||22 January 2013|
|PDF File Size:||9.93 Mb|
|ePub File Size:||2.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
You can open the file on any sound editing software and check for any extra sound peak points.
However the sound quality might not be as good as the original sound. The duration of sound that can be stored depends upon the sampling frequency and the compression technique used.
This demoboard was designed for DIP chip only. On the main window of the Writer program, select sequential key access mode. Q – The writer does not a8p9085 when the USB is plugged in.
aP Datasheet(PDF) – Aplus Intergrated Circuits
Remove or modify any unwanted sound and generate a new DAT file. Close all the running applications Like Internet, Outlook, Antivirus, and other software programs running in the background. Q – I want to use the same key play all the messages in sequence every time the key is pressed. Then select the Run the program in compatibilty mode checkbox. On the main window of the Writer program, select the re-trigger option.
Do not use USB and external power supply together. Use the following steps to check the connection: Q – I want some features to play back the IC, but I cannot find the options in the software. If writer gives error that USB not detected, then probably it is not receiving adequate power.
Remove all the USB connections other than the mouse and the writer. How I can implement that? You can provide us your requirements and we can program and compile the.
Some key points about the writer are as follows: The DAC output is dtasheet slightly amplified output has an amplifying transistor in addition. Place the jumper next to the label of the IC you are using. If your PIR module supports 5v, then you can use 5V voice chips.
Fun with sound module Writers Q – Where can I find the serial number or customer number for the writer? Contact us to purchase the item. Other OS has not been tested.
Triggers Q – I want my message to loop over and over again. What requirement or concern I should pay attention to? Q – What are the facts I need to know about the writers? You must use the same output mode to play the sound on the demoboard or your board as to what was used while programming. How can I make that happen? Programming fee might apply dataheet on your requirements. Q – I want to record a 40sec sound file to your 42 seconds chip, but I got an error. DMP file for you. Data file Q – What are the compression techniques used?
It will permanently damage the writer. You can order as individual board or as a set which includes a battery holder and 32mm speaker. The PIR module we provide is from 3. It will play all the sound files sequentially. We use the 8-bit PCM better sound quality but need more memory spaceor the 4-bit ADPCM compression techniques lower sound quality but can program longer duration as it has more memory space.
This will make the message to loop. Q – I can hear ap89805 pop sound when I replay the programmed IC.
VOICE OTP IC
How do I datwsheet PIR can be used to trigger the voice IC. Therefore, to make the sound files to play consistently, connect a capacitor 0. User selectable triggering and output signal options provide maximum flexibility to various applications. Q – I am using the writer to program the SOP. Q – I have upgraded to Windows dataaheet and now the writer does not work?
Select the Compatibility tab. How do I remove it? The serial number is provided as the Customer Number on the CD that comes along with the writer.
The PWM output is the regular voice output. You can try a circuit using an IR obstacle detector. What is the issue?
(PDF) AP89085 Datasheet download
Is there another way to program the chip? Make sure you are running on Windows XP. Select the exe file, right mouse click to select Properties.