AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Goltigis Malakree
Country: Saint Lucia
Language: English (Spanish)
Genre: Technology
Published (Last): 6 August 2015
Pages: 144
PDF File Size: 7.41 Mb
ePub File Size: 9.13 Mb
ISBN: 187-2-58519-695-9
Downloads: 94941
Price: Free* [*Free Regsitration Required]
Uploader: Ducage

When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the amefican volume should be lowered to reduce distortion.

The Output Short Circuit V Protection protects the output devices of the amplifier from short circuits and stressful loads. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. The fixture does not americn to operate normally or exhibits a marked change in performance.

Red is positive signal and Black is negative signal. Insert bare wire into the binding post and tighten. Cooling Fan – Dual speed cooling amercian. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out. Connect a XLR cable to the input of channel one. The unit also provides a way to rear mount the unit into a sudio for added security. The appliance has been exposed to rain or water.

Typical speaker output using bare wire. Ensuring proper polarity will avoid speakers being out of phase, americah can cause a loss of bass response. The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier.

You’re reading an excerpt.

Apply an input source signal to your amplifier. Turn your equipment on your amplifier should always be the last item you turn on. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. Aamerican 2 Frequency Adjustment. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack.

  DICCIONARIO DE PSICOANALISIS LAPLANCHE PDF

AMERICAN AUDIO V POWER AMP AMPLIFIER WATTS NR! | #

Detailed instructions for use are in the User’s Guide. Thermal Protection – A single variablespeed fan on the Vplus and dual variable speed fans on the Vplus and Vplus V V V amplifiers provide adequate cooling. See page 9 for more details on input configuration. These fans are used to cool the internal parts of the amplifier. Please read and understand this manual completely before attempting to operate your new amplifier.

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.

It’s a community-based project which helps to repair anything. If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Service Hours are Monday through Friday 9: It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs.

P Typical speaker output using spade connectors.

American Audio V1000 PLUS Manuals

When the input signal decreases enough that clipping ends, the limiter aduio deactivate and cease its gain reduction. Before using this amplifier, read the user manual for further warnings. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier. Turn americsn input source level up. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible.

  FASHION FORECASTING EVELYN BRANNON PDF

Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen. Connect your speaker across the red output binding post on the rear amefican your amplifier. The dip switches on the rear panel allows you to configure the low cut filter.

VLP1000 power amplifier

Be sure your amplifier and all other audio equipment is powered down. Please do not return the amplifier to your dealer without contacting customer support. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal.

Insert the spade connector in to the binding post and tighten the caps down on the spade connector. Power Switch – This switch controls the units main power.

The diagram below detail the functions of each dip switch, the functions amedican also printed on the rear panel of the amplifier. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. These amplifiers are designed to provide a big impact in sound reproduction.

The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated “dangerous voltage” within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock.